![[0{7)7UAZ(]4W{5TSMC65Q7](https://www.htsteelmill.com/uploads/077UAZ4W5TSMC65Q7.png)
Mat.No. 1.7016, DIN 17Cr3, AISI 5117, 4615
Short Description:
Designation by Standards Brand Name Ravne No. Mat. No. DIN EN AISI EC60 709 1.7016 17Cr3 - 5117, 4615 Chemical Composition (in weight %) C Si Mn Cr Mo Ni V W Others 0.17 max. 0.40 0.55 0.85 - - - - - DescriptionAlloyed carbon steel. ApplicationsLow stressed components – gears, shafts, crankshafts, connecting rods, cam shafts, etc. Physical properties (avarage values) at ambient temperatureModulus of elasticity [103 x N/mm2]: 210 Density [g/cm3]: 7.85Therm...
Product Detail
FAQ
Product Tags
Designation by Standards
| Brand Name | Ravne No. | Mat. No. | DIN | EN | AISI |
| EC60 | 709 | 1.7016 | 17Cr3 | - | 5117, 4615 |
Chemical Composition (in weight %)
| C | Si | Mn | Cr | Mo | Ni | V | W | Others |
| 0.17 | max. 0.40 | 0.55 | 0.85 | - | - | - | - | - |
Description
Alloyed carbon steel.
Applications
Low stressed components – gears, shafts, crankshafts, connecting rods, cam shafts, etc.
Physical properties (avarage values) at ambient temperature
Modulus of elasticity [103 x N/mm2]: 210
Density [g/cm3]: 7.85
Thermal conductivity [W/m.K]: 44.0
Electric resistivity [Ohm mm2/m]: 0.16
Specific heat capacity[J/g.K]: 0.46
Coefficient of Linear Thermal Expansion 10-6 oC-1
| 20-100oC | 20-200oC | 20-300oC | 20-400oC | 20-500oC |
| 11.1 | 12.1 | 12.9 | 13.5 | 13.9 |
Continuous Cooling Transformation (CCT) Diagram
Click the image to enlarge the diagram.
Soft Annealing
Heat to 800-840oC, cool slowly. This will produce a maximum Brinell hardness of 250.
Stress Relieving
Stress relieving to remove machining stresses should be carried out by heating to 650oC, holding for one hour at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.
Hardening
Harden from a temperature of 940-980oC followed by oil quenching or warm bath approx. 400oC. Hardness after quenching is 64-66 HRC.
Tempering
Tempering temperature: 150-400oC.
Tempering Temperature (oC) vs. Hardness (HRC)
| 100oC | 200oC | 300oC | 400oC | 500oC | 600oC |
| 64 | 62 | 60 | 57 | 53 | 42 |
Forging
Hot forming temperature: 1050-850oC.
Machinability
The machinability rating of D3 is roughly 25 % that of free machining carbon steel 1018. Due to its abrasion resistant nature, machining in the hardened condition should be limited to finish grinding.
Forms manufactured: Please see the Dimensional Sales Program.
Disclaimer
The information and data presented herein are typical or average values and are not a guarantee of maximum or minimum values. Applications specifically suggested for material described herein are made solely for the purpose of illustration to enable the reader to make his own evaluation and are not intended as warranties, either express or implied, of fitness for these or other puposes. There is no representation that the recipient of this literature will receive updated editions as the become available.
FAQ Content
