Mat.No. 1.2436, DIN X210CrW12

Short Description:

Designation by Standards Mat. No. DIN EN AISI 1.2436 X210CrW12 X210CrW121 - Chemical Composition (in weight %) C Si Mn Cr Mo Ni V W Others 2.12 0.25 0.45 12.00 - - - 0.70 - Description Ledeburitic chromium steel with high durability and cutting performance; low distortion on hardening. Applications Cutting tools for sheet metal thicknesses up to approximately 2 mm, paper blades,stone compression moulds, section rolling-mill rolls, deep-drawin...

FOB Price: US $0.5 - 9,999 / Piece

Min.Order Quantity: 100 Piece/Pieces

Supply Ability: 10000 Piece/Pieces per Month

Port: Shenzhen

Payment Terms: L/C,D/A,D/P,T/T

Send email to us Download as PDF

Product Detail

FAQ

Product Tags

Designation by Standards

Mat. No.	DIN	EN	AISI
1.2436	X210CrW12	X210CrW121	-

Chemical Composition (in weight %)

C	Si	Mn	Cr	Mo	Ni	V	W	Others
2.12	0.25	0.45	12.00	-	-	-	0.70	-

Description
Ledeburitic chromium steel with high durability and cutting performance; low distortion on hardening.

Applications
Cutting tools for sheet metal thicknesses up to approximately 2 mm, paper blades,stone compression moulds, section rolling-mill rolls, deep-drawing tools.

Physical properties (avarage values) at ambient temperature
Modulus of elasticity [10³ x N/mm²]: 210
Density [g/cm³]: 7.77
Thermal conductivity [W/m.K]: 20.0, 20.5 (at 350^oC), 24.1 (at 700^oC)
Electric resistivity [Ohm mm²/m]: 0.65
Specific heat capacity[J/g.K]: 0.46

Coefficient of Linear Thermal Expansion 10^-6 ^oC^-1

20-100^oC	20-200^oC	20-300^oC	20-400^oC	20-500^oC	20-600^oC	20-700^oC
10.8	11.8	12.4	12.5	12.8	12.9	13.0

Continuous Cooling Transformation (CCT) Diagram

Time-Temperature Transformation (TTT) Diagram

Soft Annealing
Heat to 800-840^oC, cool slowly in furnace. This will produce a maximum Brinell hardness of 255.

Stress Relieving
Stress relieving to remove machining stresses should be carried out by heating to 650^oC, holding for one hour at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.

Hardening
Harden from a temperature of 940-980^oC followed by air,oil quenching or warm bath quenching 500-550^oC. Hardness after quenching is 64 HRC.

Tempering
Tempering temperature: See the data bellow.

Tempering Temperature (^oC) vs. Hardness (HRC)

100^oC	200^oC	300^oC	400^oC	500^oC	600^oC
63	62	60	58	56	48

Tempering Diagram

Forging
Hot forming temperature: 1050-850^oC.

Machinability
The machinability rating of OCR12SP is roughly 20-25% that of free machining carbon steel 1018. Due to its abrasion resistant nature, machining in the hardened condition should be limited to finish grinding.

Disclaimer
The information and data presented herein are typical or average values and are not a guarantee of maximum or minimum values. Applications specifically suggested for material described herein are made solely for the purpose of illustration to enable the reader to make his own evaluation and are not intended as warranties, either express or implied, of fitness for these or other puposes. There is no representation that the recipient of this literature will receive updated editions as the become available.